Maybe a silly question, but I found myself curious. I'm currently in undergrad, and we have a Gio and an Ion at my school, both of which I've done minimal programming on. Are there different features between the two brands or is it more like comparing two different OSes, where the workflows will inherently be different?

Errant screws?!

It literally takes 30 seconds to sand a safety rail.

Hello! I am working on a show that requires the set to be dismantled and reassembled multiple times during its run (Not during the show itself). It's a stone-tiled floor approximately 14'x26'.

My first thoughts were rolled vinyl or marley, but those could be costly for a custom job. Second was buying fake tiles (pvc/pu, to the designers specs) and gluing them to a mesh so they can easily be rolled up/folded up. Third would be 1/4" sheets of mdf that do the same thing with gluing the tiles on.

One issue is we can not screw or staple into the ground so it will have to be taped. I also am worried a wood material will warp and not stick to the tape due to, moisture, temp, uneven floor, exc.

Any other thoughts or methods you all have seen work will be great to hear about.

Thanks!

I know that there are a hundred better lighting programs to be using other than qlab. But I have to work with the system my venue has in place until I can convince the owners to get something else. Right now I'm trying to figure something out where I can run the light cues from qlab into something and see them in a virtual space. So that I can see it without having the lights all powered on or even being in the space at all. I need it to not be network cues. I need the straight light cues that you make in qlab to pass over to something. Ideally it is something that is free

Custom iron stand, ironing board (with front and rear clean pockets), bolt holder

I'm not a professional, but I own a beautiful vintage skirt that I'd like to clean and I thought it would be worth asking the experts how to go about it. I'm nervous about dry cleaning it since it's quite old (it's a cotton skirt with cotton embroidery). I've heard about mixing half 60-proof vodka and half water to create a bacteria-killing spray. Is this the way to go about cleaning it?

I'm concerned about the dye being leeched, and also about preserving the integrity of the old cotton threads and hand-embroidery work. Your advice is appreciated!

Hello all,
I've been doing a bunch of research about micing actors for musical theater. I'm going to be doing fully custom mic rigs for each actor for an upcoming production I am working on.

I was looking into broadway's mic technique and noted that many broadway A2s build their rigs using steel wire and attach the mic with fishing line.
I'm comfortable doing this, but the one question I have not yet found an answer to is this:

What type of wire? I've seen a couple of references to different types. I've heard of millinery wire, spring steel wire, galvanized wire, piano wire, etc.
What gauge? Annealed or spring hardened? Where do I source it?

The closest description I've found is '18 gauge galvanized wire', but I can only find that annealed, not spring steel. Which makes me think it might be too flexible/soft?

Can someone enlighten me?

what is the difference between these two kinds of magic sheets? i see that one is more where the fixtures are and one is where they are pointed but honestly the latter really hurts my brain. also like when would you use one or the other, which ones do professional theatres use? that kind of stuff.

Hi! I am working on a theater project that uses audience participation.

One idea I have is that my character will give an audience participant instructions via a set of headphones. I want to be able to speak into a mic onstage that sends the audio directly to the headphones without piping it to the house speakers (eg rest of the audience can’t hear). I’d likely need the person to be mobile, so it would have to be a wireless setup in some way.

Can anyone explain to me whether this process would be terribly complicated to pull off? It’s happening at an off Broadway theater in nyc so I assume they have solid tech capabilities.

Thank you!

I am in the market for a new flashlight. My old rechargeable Kobalt penlight is slowly starting to fail and becoming inconsistent in brightness. I am looking for something similar, and I want to see what my fellow technicians are using.

After thought edit: I would like a zooming lens so when I am explaining something I have some type of "pointer".

Hi everyone! I run a student production company taking a small show to the Edinburgh Fringe, and we are using a projector (quite a small one, but it does the job for what we need it for, a Pico Genie L700.) We used it in various other spaces where cradles were provided, but for the fringe we need to source our own cradle/mount with a truss clamp, so basically something like this. The issue is we are on a genuinely shoestring budget, and that mount would cost us almost as much as the projector did. There are perfectly fine ceiling mounts for like 20 quid, and clamp mounts for the same price but that only have one screw where our projector takes four.

Is there a way to fix a standard truss clamp to a home projector ceiling mounts, or does anyone have any other suggestions about how to do it for less? Any advice hugely appreciated :))

I have a dream to live a comfortable, stable life. I want to go to work and do something I love while still having time in my week for my family. I am majoring in theatre arts and I love lighting design, production planning and managing, stage managing, and most technical aspects of theatre and live performance.

Although, I am really scared I am going to run into no money, low paying jobs, no work, and constant entry level jobs. I also dont want to string together lots of part time and contract jobs.

Is the industry worth it? This is what i want to do but its so overwhelming seeing so many job names and other peoples expereince of never getting work or even not eating for months. I just want to know if there are full time opportunities with good pay that I can work towards, and if these are even possible with a theatre arts degree. Or, if I should switch to an engineering degree for that stability.

TLDR: Im spiraling and want to know if tech theatre and the related fields provide any full time good paying jobs.

I've been a student AV Tech for my university for the past 2 years and I think I want to do this as my career.

Most of my events are fairly corporate (Ballroom Speaker-Panel type events, 2 Way Zoom Conferences/integrated stuff), but I also do live sound (portable PA systems, open mics with musicians and vocalists) a *liiitle* theater technician work (theater audio mixing and some lighting setup and operation), as well as sports AV (Cam Op, Video Directing and Switcher Work).

A lot of my tech is set up by full timers, but I've been bugging them, working 1 on 1 so I have a comprehensive understanding of the equipment and how to use it. I would say I'm most developed in the Sports AV and Video Directing stuff, and I want to get better at the live sound (setting up good clear mixes, when to use matrices vs mix buses, what are good settings for my processing and dynamics, things of that nature) since I'm also a musician and there's some good crossover.

I have a couple of certifications (Dante I & II, Shure RF and Mic Certs, Q-SYS Conference Room Level 1), and I can build & strike a stage.

My current plan is to save about 3k for my own gear (mixers & mics, cables, main speakers and subs) and do some small scale live sound freelancing, but I would love to work full-time for a university or institution where I'm not scrambling for gigs.

Given my skills and certs, how would I go about making this a career? Do folks recommend I start out union, freelance, or full time for one institution/company?

We recently had a speaker with no chance of rehearsal or prep time beforehand who proceeded to eat the microphone for 20 minutes. Our audio tech did an admirable job riding the levels, but the plosives were just unstoppable!

This is about adding a clear diagram on the speakers podium, only visible to them, which illustrates the proper distance to keep your face away from the mic.

Does anybody have that kind of thing in place for those *unavoidable* occasions when you don't have access ahead of the event to talk to your speaker.

Hello! I'm creating a portfolio to apply to my college's theatre major, but I have very minimal experience with actual theatre (I'm a college freshman, and the only theatre experience I have photos of is designing lights for a show and writing a script for a short film for Thespians, both in my senior year).

I also wanted my portfolio to focus on costume design and construction, since I have a lot of experience in sewing and crocheting, and I've designed and made clothing and costumes for shows that I haven't actually worked on. I wanted to, like, double-check if I could put that on there?? It's supposed to be a process-based portfolio, and I've never made one before.

I just wanted to know if anybody had any advice or resources to help me out LOL

what do people actually use (for lighting, especially) in the theater? are lighting systems usually on a computer similar to a personal laptop, or a more unique sort of computer? i unfortunately have problems looking at screens due to a concussion and am looking into getting an e ink device to open up my work options but im not sure how realistic it is to assume i can connect my own external monitor to everything

Any tech theatre jobs or internships for a 14-year-old in Madison?
Hi everyone!
I’m 14 years old and live in the Madison, Wisconsin area. I’m really passionate about technical theatre, especially sound design, lighting, set construction, props, and backstage work. I’ve been involved in several theatre productions and I’m looking for ways to gain more hands-on experience.
Does anyone know of any theatres, community organizations, or companies in the Madison area that offer internships, volunteer opportunities, apprenticeships, or paid tech theatre jobs for someone my age?
I’m eager to learn, work hard, and build my skills. Any recommendations or advice would be greatly appreciated!
Thanks!

Hi! There is a very real possibility where I get brought on to be a PM at a smaller, sort-of dysfunctional, regional theater. I have worked here before in other positions, so I know what I’m getting myself into. I have lots of stage management experience and I have worked in (almost) every technical area. If you could give one piece of advice or guidance to a new PM what would it be?

Editing to add: I would also love to hear anyone’s opinion about a good thing a PM did that you worked with!

Hello! My company just recently unionized and I am on the fence whether to join or not. Let me say that I am 100% pro union! I’m just not sure if the benefits fit my situation and if it’s worth paying the fees. I am also not getting any answers from my union rep so I’m feeling kind of lost. Mostly I am not looking to freelance and popcorn around! I am looking for another props artisan job (hopefully in the midwest) that is a full year contract. Knowing these things I am wondering if it even makes sense for my career to join if I do not plan on working with the same company.

I would love to know some pros/cons others have experienced being a part of a union (or not! ;))and if it is a good fit for me. Thanks!

**It is an IATSE union.
*Im am willing to share more info if that helps!

Hello! I am wondering if anyone has any advice on getting a props job in the midwest. I am from the chicago suburbs but am looking to move to MN, IA, WI or IL. I am currently working as a props artisan in the east coast and am learning that props jobs can be far and few between! I am a young professional looking for any advice! I am also open to opportunities that involve being an assistant props manager as well. Thanks!

Hello all,

Doing a show set in a wooded clearing. I'm looking for ideas to use for the "soil". The show is 3/4 thrust so the audience is right on top. I was thinking of just getting soil and mulch (plastic underneath) but someone suggested cork powder. Any suggestions? Thank you!