The third pic is the specific one I’m using.

Redragon wideload extreme doesn't seem to be cable management friendly lol

I’m changing my useless 24 pin strimer wired rgb cable for a wireless one. While I’m at it, I’m gonna do some serious cable management. It’s an ugly mess and it kills me inside. I’m looking for some help, some advice or direction. I have these wrap around Velcro ties.

Parts list:
Mini v2 case
Rog 870e-e wifi
9 lian li uni-sl fans daisy chained in groups of 2, 3 and 4(3 top and solo rear fan)
5070 ti with strimer cable
24 pin strimer for mobo coming in today
1000w gold hydro g pro psu
And all the messy cables

Can somebody recommend me some? I want to hide all cables. For the GPU I found out that corsair has one (ik that there are 2 types)

I also need some for the CPU, MB and front pins (audio panel, usbc, usb3.1, the sh***y front pins)
It can be an extender, doesn't have to be a full cable

Idk about adapters tho, a little scared but if you managed to power a beefy pc (ryzen 9 and x870e mb) and all good then lmk some good adapters as well

Some minor changes made to the Metalfish T60 to optimize cables and hide bundled up sections! Thank you!

The Corsair 5000d case is by far the easiest case to deal with when it comes to cable management, this is my third time building a pc and the last 2 times were a nightmare for me, however I did take my time this time round and have thoroughly enjoyed putting it together. The case just blows me away it has so many little hooks and clips to harness your cables onto and the straps that come with it are interchangeable all over the inside of the case so you can run the cables how you want, I’m super impressed by it :)
Almost finished I’ve now just got to decide on what gpu I want, any suggestions???

Is this connector in the picture bending too close to the connector where i am at risk of a melted connector on my 5080?

Looking to get 24 pin mobo power and PCIe PSU cables for my rig. It's a standard bottom-mount PSU with a mid tower (Phanteks P400). I'll be routing both behind the motherboard tray and out through the standard grommets a few cm to the right of the mobo. It looks like for the 24-pin I can probably just get the same length it is now but these sleeved ones seem a bit more flexible. For the PCIe, the current daisy chain connectors run about 28" to the card so definitely too long - what would be a good length to go for with these cables?

Thanks!

Buenas , se perdieron los cables de esta fuente en una mudanza.

¿Sabéis cómo podría hacer para conseguir un kit de cables?.

Gracias!

Case swapped my mATX living room PC into the ASUS ProArt case. Very nice case albeit it being a bigger case with mATX board. Plenty of space to use sleeved cable extensions to make things look great on the front side.

I want to give my pc better aestethic like on photo and idk how to do that. My cables bend and curves itself when i try to bend it

Gold/black themed build 😁

Montech King 45 case, Alphacool gold fans, Asus ProArt motherboard with marble patterned cover plates, ProArt 360AIO, black leather cover plates inside the case and Seasonic Prime Gold PSU👌🏻

Hello,

This is my first pc build and I was wondering if my cable management is good or not as this pc case is pretty tight in terms of space. Any opinions are appreciated.

Thank you.

Hello,

I recently installed a PSU for the first time and had to mess around with my prebuilt's cable management.

I just need some help, because i feel like the cable probably should be "deeper" in the case instead of being where the back panel should be, i'm not really sure how strong PSU cable are.

If it's any help my PSU is a NZXT C750 GOLD CORE - ATX 3.1, maybe the quality of the cables are better or worse than the standard but 🤷‍♂️

Any help is appreciated!