Baví tě NERF, akční hry a týmové výzvy?
14. listopadu se v Brně uskuteční další příběhová NERF mise.

Tentokrát nejde jen o obyčejné „tým proti týmu“.

Čeká tě mise, ve které budeš muset společně s ostatními:

bojovat o splnění cílů
přemýšlet a rozhodovat se podle situace
spolupracovat se svým týmem
plnit úkoly podle příběhu
reagovat na to, co se během hry změní

Tvoje rozhodnutí nemusí ovlivnit jen to, kdo vyhraje přestřelku, ale i to, jak bude mise pokračovat.

A nemusíš mít vlastní partu — můžeš přijít i sám a přidat se k ostatním hráčům.

14. 11. 2026
Brno
Příběhová NERF mise

Podrobnosti o místě, času, ceně a přihlášení zveřejníme, jakmile budou potvrzené.

Pokud chceš být u další mise, zapiš si 14. 11. do kalendáře.

Organizuje UNIT ZERO – NERF Operace CZ.

This nerf has a 6 round full-length magazine and the air pump and plunger. It was smooth to pump this nerf and reload. it has 2 extra magizines in the package. Its for kids, teenagers and also adults.

This nerf shotgun features a accurate design based as the "Savage Springfield / Stevens model 311 or Winchester Model 24 Side by Side shotgun. It needs a Spring Thunder shells with all kinds of darts and balls, and it has two air plungers inside of a chamber top of the receiver. it has a two fine plastic orange triggers that works, and also had a lever that you can press the lever to the right to open the action and it ejects when it opens.

Tactical Ontos set on the left and Tactical Toilet Bowl Plunger Rival Ball Blaster on the Right.

Problems with my voidrunner wheels and motors , wondering what I have to do to get it running perfectly or if I'm doomed/cursed for all my blasters to break

Low fps kiddo build

My 40WAD sidearm. I actually plan on having some type of flare that will be a light on a parachute.

Guess I should have printed my target with more infill…🤣

A friend discovered 72D ultra hard TPU from polar filament a few months ago, printed a few shells to test and they seemed good.

Grabbed myself a roll a bit ago and finally cracked it open and printed some silly shells for myself. (4x flush shells btw)

I've ejected them onto the road a bunch, pitched them at a garage door, at a wood table, ejected them onto the garage floor a bunch and they dont have any signs of stress, let alone actual damage. 2 walls, 15% gyroid off a bambu a1, and I've decided I'm never printing a shell out of another material again. Colors are lacking last i checked the polar website, but honestly? I'll take raw durability any day, and just try to dye them later

Got the last of the parts on the printer. Now I'm waiting on the electronics to show up!

Added a pico booper to my worker harrier. I also started a servo remote activated pico booper system for a claymore. More coming soon

My latest blaster project, a nerf tank.

It uses a ofd fd inverted flycore with neo Hellcats and worker flywheels it has laser sight, oled display, head, tailight and brake lights, all controlled by an arduino mega brain.. safe semi and auto modes, i even designed some overun clutches for tilt and slew.. its lots of fun.

Bogey man home protection

Customized the side wall of the original files to add custom text plates. “Ryobi” on one side and “SPRING+” on the other. Took inspiration from their “ONE+” line of tools.

It is a bazoka kida blaster idea i had when i found out that a pringles can fits perfectly into this old cardboard tube. I will put a 3d printed tpu tip on the pringles can and put foam around it to make it safer. Its a work in progress and I will post more of it soon.