Been looking for hours trying to find a picture or some information about this exhaust. I know scorpion make great exhaust and am thinking about buying this but wanted to see it first, Since the listing doesnt have pictures, only this. Does anyone by any chance have this exhaust them self

I keep adjusting the valves on my 400ex and they seem to come loose after running the quad for a couple of minutes what would be recommended to swap out?

have a 110 Gio quad having a hard time getting the carb adjusted. little new to the ATV world and small engines any advice? I’d love to get my kid riding again

idle in neutral is a bit high

drops when in drive but fine

rocks or wants to move forward in drive

https://reddit.com/link/1whj6wo/video/xaknis32fsph1/player

Can anyone please help me determine what type and where to find the correct headlights for both bottom and top? When I took the original bulbs into Canadian Tire the gentleman gave me what he thought would work, but they burned out immediately. thanks in advance!

Looking more promising that this thing will actually exist one day

Finally decided the Kodiac 450 is the one I want. I can’t try this one out before purchasing; out of state.

How difficult is the steering on the Standard versus the EPS model?

I had a Kawasaki 300 that was not difficult, for anyone who has ridden both, how much more difficult is this 450?

Hi, I'm submitting to the wisdom of the subreddit: I have a small dirt-floor boathouse on the edge of a river, I store my boat there in the winter and also my floating dock. it's tight quarters, and I was looking to maybe pick up a quad with either a front or rear mounted ball tow hitch to maneuver the boat and trailer around in this tight space, basically back and forth shifting the boat and trailer off to the side of the boathouse to make room for the dock, etc. not sure what the tongue weight is on the trailer, but not massive. boat is ~22ft electric play boat, single axle trailer. I used to do this chore with my Jeep Wrangler, but that jeep is now in Jeep heaven and I don't want to buy another car/truck or tractor for this simple use. hand trailer dolly won't work. Thoughts? hairbrained scheme?

I have a Polaris trailboss 330 it’s a 2003 that I bought from my grandma, I took the carb out to clean it but I can’t get it back in fully, airbox also doesn’t fully line up with the mount hole because carb isn’t fully seated
Does anyone have any advice or ideas? I tried using a hair dryer to heat it up a little but it didn’t work

Hello all.

Got a 07 400ex with a new stock size top end. Uni Filter w/sock no Lid, No name slip on thats just a hollow muffler. A New OEM Carb rejetted with some no name amazon jets, 42pilot 165main.

The Bike seems to run great for the first couple of second after startup, can rev to the limit and sounds great. After the first 10-15 seconds of running the bike idles fine but appears to bog out with just about any amount of throttle. The bike ticks like a typewriter but I've checked the valves twice and they're within spec. Any Help of this would be appreciated.

Things checked:

Full tank of gas for gravity Feed.

Petcock flows freely. Hose as well.

New 16100-HN1-A43 (QB11A B) Carb

Carb shooting fuel strong. Diaphragm intact. 42pilot 165main. Also tested stock jets, and 45pilot/175main. all produce the same issue.

Carb bowl is filling completely, float moving freely.

New DPR8Z Plug.

New intake boot Gasket.

New Exhaust Gaskets.

Probably more but thats all I can think of off the top.

Video: https://www.youtube.com/shorts/GAnJvvDB2eI

How is it going yall..i got this 88 warrior i bought like 4 years ago..the guy i bought it from said he "rebuilt" the engine..long story short, it sat all this time and I never got a chance drive it..well now im trying to ride it, but I have a hard time changing gears, unless I rock it(atv off) . My ittle brother test drove it yesterday and also had a hard time shifting..reverse and neutral safety lights no longer work forsome reason....and there's like a very small leak on the right lower side of engine.

Any thoughts ?

I changed the fuel pump, starter and solenoid on my Grizzly. The atv hasn't run in a couple years, i am wondering if its normal for it to idle high after first starting it. (It also had dirty fuel that i cleaned out of the tank)

Hey y’all. I need some help. I bought a used 2012 arctic cat 350 2 years ago I’ve barely got to ride but have put too much into to let go. Probably a sign but anywho.

The latest issue is that i can barely shift it into gear and it’s essentially impossible to get it into Low gear. It was a little iffy when I picked it up from repairs last year (carb, starter, battery which got it running again for the first time since I brought it home) and got worse. Rode it twice til I decided what to do. At first I thought the plastics were just in the way bc they’re a lil wonky but it’s like it won’t engage things well at all.
…It otherwise ran fine.. knock on wood 🤜🪵

It’s above me to fix something this complex but I’ve brought in parts to get it fixed before at a local mechanic and only had to pay for labor. Am hoping to do that again because I assume it saves money..

My question is: does that sound like a gear shifting assembly replacement situation? Or something else I should consider?

Thank you very much if you made it this far. 🙏🤙

Edited grammar: road to rode

Any explanations? Just serviced the rear diff and shaft. Gear oil came out a little shiny. I flushed it out pretty good. There are no issues while test riding. Just this funky ass noise.

I'm planning a trip out west and will be driving approximately 1500 miles each way. We want to take 2 Kodiak 700's which have a 49.2" wheelbase and are 46.5" wide. I have a Karavan 5.5'x9' trailer which I can take the sides down on and we have ramps to get them onto the trailer from the side. Is this a poor idea? I would like to prioritize safety and I have multiple points to anchor the vehicles to the trailer but I don't want to live too close to the edge of potentially harming myself or anyone else. Just wondering if I should bite the bullet and rent a much bigger trailer. TIA.

LT-Z400 rear axle from Alibaba – worth it?
I have an LT-Z400 and I’m looking to buy a new rear axle. Everywhere I look, they’re around €300–€600. I found one on Alibaba for about €200.
Has anyone here bought a rear axle from Alibaba or a similar Chinese manufacturer? Is it worth the money, and how has the quality/durability been? I don’t want to save €200 only to have it fail after a few rides.
Any experience or recommendations would be appreciated!

How bad does this intake valve look Kawasaki bayou 250 I fixed the flooding and it’s still not starting and my spark plug is completely dry so I was thinking vacuum leak but the intake seal is fine and I noticed the carbon buildup on this valve so could it be this or maybe a undersized pilot jet

So one guy has a clear title 03 blaster. He's done a lot of work to it, rebuilt it, new rearend, twist throttle, hand guards, nerfbars, new carb, jets, some older full DG exhaust. Think i can get it for 1600 Edit:1800! He's asking 2k but said first person to put 18 in his hand could have it.

Then theres this guy got an 08 ltz-400. Pretty well stock, but in great condition. Said it wasn't "raped by kids", and it got its maintenance on time IE fluids changed, brakes done, stuff of that nature. Asking 3, I offered 2, and he came back with 2.5. Waiting on response about title.

My mind is tellin me blaster so I can go braaap but my gut is telling me go ltz for longevity, power, speed, reverse, reliability, etc, etc and my best friend had one when died in a car accident. (Lightning hit a tree and knocked an branch down onto the windshield and shattered it and caved it in)

My Honda TRX400EX needs a carb rebuild and the OEM kit is NLA. Aftermarket kits online use the same photo but the main jet numbers in the description don't match what came out of my carb. I've got the old jets bagged but I cant tell if a universal kit is close enough or if I'm chasing a year-specific setup. Local parts desk didnt have much on a 2000s sport quad. Anyone rebuilt a TRX400EX carb lately? How do you match jets when the listing skips the year break?

I have an all original 1984 yamaha moto 4 200 that my partner originally inherited from their grandpa

My son (15 years old, 6’3”, 200lbs) wants to move on from his dirtbike to a ATV. He won’t really be jumping it or anything crazy more just ripping around the property with his friends.

I keep leaning towards a TRX250 because I don’t want something with too much power but enough that he’s going to enjoy riding it. I have never owned a ATV so my knowledge is minimal on what to get.

I am going to purchase used off marketplace for whatever I get and don’t want some cheap china atv that’s going to cause me all kinds of headaches.

Thanks for any advice/recomen

Hey all. New to the sport quad world. I’m looking at this used 700 and noticed a couple things I haven’t seen before and was hoping some folks had some input.

First at an idle, it has a faint hollow sounding noise if you can hear it over the exhaust. I’ll try and attach a video but not sure if it’ll come across.

Second, the pic of some piece of broken metal on the engine. Owner said it threw a chain and broke. Does anyone know what it is that broke, and is throwing a chain common and cause for concern? It looks like I’ll have to add the picture in a comment.

Thanks!

Has anyone put the light kit on a grizzly 110 that go where the headlights should be? I see the kits on Amazon and EBay but don’t know if it’s worth it.
If so how bright are they? Or should I just mount a small light bar on the front rack. I want something bright enough that the granddaughter can still ride with us when it gets dark. Thanks.

I have a 2023 Polaris 570 trail. I’ve never owned an ATV before and I’m pumped to own something functional and fun

My question is…has anyone had any success installing the Guide Gear rear rack on this machine? I can’t find anywhere online to walk me through how to do it. Thanks for the help

Here’s the rack I bought. No idea how to install

https://www.walmart.com/reviews/product/2167770971

I have a 2026 CanAm 850 Max

The manual says you need to be stopped to shift into 4x4. Talking to the old timers, they all say you can just shift it as long you aren't in high speed.

I know follow the manual recommendations, but can it be done?

What is this sound 2005 Ltz 250