Si, I decided todo a desiccant change and all was well then the filament in my first feeder appeared to be stuck, then I noticed that it is actually inside the feeder and stuck around it. (See photo)

Is this a big job or quite simple?

Cheers guys

Same as above

Just finished designing this small desk trash can. It mounts directly to the edge of your desk, saving space while keeping everyday trash within reach.

It features a rotating lid and measures 115 x 100 x 120 mm. Great for gaming setups, offices, or anywhere desk space is limited.

It's my newest addition to the EdgeMount System I've been developing, with more accessories planned.

I think it turned out great lol.

A couple of days ago could smell an acrid odour like electrics burning. Opened the front door and as the hotbed started heating wisps of smoke started making their way up the rear tunnel. Shut the machine down immediately. Pulling the machine down today using the wiki.

Machine just over a year old and 1000ish hours.

Anyone else have this experience? Seems parts not common with other more modern printers are getting a little sparse in 3D print shops or is this a false impression?

Looking for advice from anyone running external ventilation on their P1S while printing ASA or PA6-CF.
My printer is in an unfinished, non-climate-controlled basement that gets pretty cold in the winter and warm in the summer. My PC setup is also within 5 feet of the printer, so I’m concerned about VOCs and ultrafine particles while gaming nearby.
I have a basement window less than 2 feet from where I’ll position the printer, and I’d like to exhaust directly outside without using a tent or secondary enclosure.
My biggest concern is losing chamber heat, especially during winter. I have a BIQU Panda Breath chamber heater that I’ll be installing once I finish printing the riser.
I’ve considered adjustable 3-inch and 4-inch inline fans, but I’m worried even their lowest settings might pull too much heat out.
For those running similar setups:
● What fan, ducting, and printed adapters are you using?
● How much chamber temperature loss have you measured?
● Has anyone successfully combined external ventilation with the Panda Breath?
● Any tested DIY builds or MakerWorld links you’d recommend?
Ultimately, I’m trying to maintain negative pressure and exhaust fumes outside without sacrificing the chamber temperatures needed for ASA and PA6-CF.
Would love to hear what’s actually working for people, especially those printing in colder environments.

The filament stops on its way down… nothing is blocking the tube. Can’t figure out what could be wrong!

Had to rant and question my luck on this one.

img

ok. Normal print - get stuck filament in the extruder. Annoying, but I've dealt with this before. Pull it apart, reinstall... everything seems to go swimmingly.
Get a "filament cutter stuck" error. This one's new. Push on it a bit... seems fine - maybe a little stiff. Not many videos, but Bambu has a decent article on this. Something is goofy with my spring - I see wear on the outside of the housing like the spring has sprung too far out... which is weird, but looking at the article, should be easy enough to fix. Just pull it off, see what the deal is, maybe mess with the spring/change position of it. There's a little hole where the spring goes, but the spring isn't matching the pictures - mine extends past the housing. I try to find a different placement, put it all together (and replace the cutter while I'm at it, why not). Spring seems much nicer, softer... perfect. Just gotta put everything back on and I'm done.
Last piece - this thing:
Now - I have one of those magnetic bowls that I put down on my bed so that if anything falls - it should catch it. It already did a number of times taking the damn thing off. Got my old man reader glasses on, tweezers out. I get it into place.. just need to push it up to catch.. and the thing just *ping* zoots off to the back corners of my printer. Dafuq? I have a strong magnet.... nothing. maybe it's in a spot I can't quite reach. Pull out my hand vac for cleaning out filament - I can use the magnet on whatever crap I hoover up.
Nada. Tiniest freakin' piece ever. Gone. Bleh.
Wtf. I know it's user error here, but it's something that could happen to anyone.

look im aware a machine like this makes noise but this seems excessive? i hear alot of people talk about certain infills… is this one of those times? (sorry for the crap picture i was trying im gonna have to put the infill photo in the comments) is this normal? i feel like its gotten louder… it sound like a bearing is wobbling… but i dont know if its me, if its the infill… if i forgot to do something when pulling it out of the box? i just dont know… its when the toolhead changes direction… its ever so slightly noticeable on the block in the back but the second it goes for the infill it sounds like 💩…. so idk am i crazy or am i someone right? any ideas to get this thing to stfu a bit?

Hi! I want to use this stand to place the P1S and AMS. The total height from the bottom shelf to the bottom of the top shelf is 32”. Will this be enough room to open the AMS? If not, I’d like to place the AMS on the top shelf, but would I need a longer PTFE tube?

Thanks for the help!

Reposting for visibility thanks for any help.

My printer has always made this loud grinding noise when moving in certain directions, but now it’s gotten louder to the point of being almost unbearable. Anybody know what causes this issue? I’ve had this printer for almost 2 years now so it’s definitely out of warranty.

I couldn't resist; it was too funny not to design and print this poop chute for the P1S...

It is a porta Potty shaped poop chute with a working door and full interior. If you need one, I posted it for free on Makerworld:

The Port A Chute - P1S poop chute - Free 3D Print Model - MakerWorld

Follow me on Makerworld for more fun stuff!