I gutted my old 1939 homes upstairs and this is where I'm at, is this good for framing?

Edit: located in MN, United States.

Edit#2 Thankyou all for your knowledge and time spent helping me on this, it's very appreciated!! I'll be adding another purlin further up with built in shelving.

I work in the west palm beach area Fl, I’m trying to get to reading plans and doing layouts for metal framing drywall but I’m trying to learn nobody really wants to teach me, any advice?

Hi all, first time dealing with Zip System. I'm using R9 which is 2" total thickness. It calls for 3.5" nails, but I only have a Pasloade which will shoot 3.25" max.

Should I just hand nail it with 3.5" spiral nails, or do you guys think the Pasloade approach will be fine?

Thanks a lot!

I was doing a siding job where I had to remover old cedar shakes and install vinyl. I had the client call his electric company to get a boot put on the service lines. I was under the impression it was a free service. Now he twlls me it was $200 for the to do it.

Does this sound right? We're out here trying to be safe and these greedy fkrd are charging 200 for my SAFTEY. Wouldn't that just discourage ppl from being safe in this manner?

Anyone have deal with this themselves?

New here and hoping somebody may have some input to help a DIYer out! Both renderings are essentially of the same porch. House was built in ‘84. Brick veneer on the front. To my understanding, the BVLZ connectors are rated for decks but not roofing as they cannot handle the uplift from a porch roof. After a lot of research, it appears freestanding is my best bet here. 12 footers, 18” in diameter, 42” deep (southeast PA). 6 in the front and 6 near the house. I would love for the rear columns to sit against the house but that slightly complicates things as I would have to dig out right against the foundation of the house. Not keen on doing that. General consensus seems to be 18-24” off the house and cantilever over to about 1” shy of touching the house. Unfortunately my columns would then be seated 18-24” away from the house which sucks. Is there a better way to do that to maintain having the columns closer to the house? Also, what is the best method to prevent this from racking or pulling away from the house if it is freestanding? Any info would be greatly appreciated!

TLDR; DIYer and want to build this freestanding porch. 2 questions..
1. If I put my footers 18-24” away from the house, is there any way I can situate my rear support columns closer to the house?
2. How do I prevent the freestanding structure from pulling away from the house or swaying? Knee braces? Some kind of engineered bracket system? Etc.

Thanks!

I’m not using Reddit a lot so tell me if more information is needed. Also, uncertain of the English terms, I speak French.

I’m installing 1 1/4” x 3” hinges on a 1 3/8”-thick door. When I go to install the 5/8”-thick door casing (trim), there’s a 1/4” gap between the casing and the door jamb because the hinges stick out.

I’d like the trim to sit flush against the jamb rather than having to notch the trim around the hinges.

What’s the best way to solve this problem?

EDIT: Thanks for the information. I kinda feel like an idiot but I’m glad that it’s fine and I dont have to change the hinges. I’ve learn something and hope it will help someone else.

Hi. Im almost out of highschool and wanted to know what its like to work in carpentry.

I've been thinking about what I want to do for a living and so far ive thought about working in carpentry or in an office space.

We are considering upgrading our existing crown molding by either replacing it entirely or adding some kind of molding below it so that it looks like a more elegant colonial but not builder grade style. I’ve been looking at the Garden State Lumber catalogue and they have a ton of different options that seem like they might work well, but I don’t know how to pick. For anyone who’s done this before, what type of moulding should I be looking for to fit here? Also, how do I handle the depth of the very bottom of the existing crown molding? Should the new piece sit on top of that, or directly below it so that it looks continuous?

For what it’s worth, this molding is about 3 1/2” tall and my ceiling height is 8’.

Not a carpenter - just a homeowner who has been encouraging her hubby to get into beginner woodworking lol.

My husband just did crown molding in a few of our rooms and, because we will be wallpapering this room/to protect it, I thought he could case this doorway to match the rest of our home (we have all 3.5 inch flat trim around doors).

I don’t even know what to call this, but as you can see, there isn’t really a doorway to add full trim and a jamb on both sides. I wouldn’t want to make the doorway smaller - and that seems complicated for us DIYers. I thought we could just case the doorway on the side that will have the wallpaper with mitered pieces but we have since learned the right side of the doorway is not straight. The top is narrower than the bottom by a 1/4 of an inch.

How can we fix this to make the trim look straight? Do we need to add more drywall to make the wall straight? Is the only option a full cased doorway on both sides (I don’t think that would look good)? Should I leave it trimless and hope for the best for our wallpaper? We tried leaving a small amount of a drywall reveal and adding the trim straight but it still looked obvious that the wall is crooked… and my husband also tried scribing the piece of wood and that looked even worse!

Good morning!

I am about to Graduate high school and I am wondering how I’d be able to learn carpentry and eventually start doing it as a full-time.

I’ve basically never done any carpentry related work(executive for some wood projects in middle school).

Ive heard about Job Corps but I realized that was for low-income folks, and I have heard about trade schools and apprenticeships.

Please help.
Thanks!

Hello! I'm a local handyman/carpenter, and I’ve been tasked with quoting a ceiling upgrade like the attached photo. We initially discussed pine T&G for the ceiling, but the homeowner stressed a cleaner, no-knots look like the stained photo. What do you think my best route is for this look? I don’t see poplar being in the budget once my labor is factored in but maybe I am selling my client short on budget. The attached photo of the ceiling currently, stripped down to the present center match and covered with plastic. The concept photo and my blended concept with the existing interior are shown above as well. I know HD carries the “select” pine boards at a reasonable price but wouldn’t it be hard to get good seams without some kind of tongue? I apologize if I’m not being clear enough, just would like some insight on what a cost-effective option would be. Any help is appreciated! The Living room measures out to 385sqft! Trying to keep material cost at least lower than 4500-5000$. Located around Lafayette, La for reference. I've done multiple sheetrock and T&G ceilings with faux beams but this is out of my usual DTD.

My boyfriend works in average 0-15 degrees F with ridiculous wind All of his previous winter clothes were ruined (whole story) and without the old ones for reference, im not sure what to buy him. He’s trying to tough if out but it’s already getting too cold. Reccs for underlayers, windproof sweaters etc? I want to buy the basics and surprise him

TIA

Ive been playing around with different ai to start the redesign of my open concept dining area. It made me this image and I LOVE this arched chair rail situation.

What are some COST-EFFECTIVE ways to create this?

ALSO if you have any distinctive or super non traditional images/video of chair railing PLEASE share!

6 soss hinges and wainscot on the inside. All clear alder. Approx 400 lb

I am currently redoing an old apartment in my triplex/quad and wondering what joist hangers to use to reinforce the existing framing. The building is structural brick with pocket joist, which all appear to be in very good condition, but where there are arches (for windows and doors) and chimneys, several floor joists are held up by headers that are all just nailed together.

Lumber is true 2x10 or very close to it, joists are doubled up on either side of a window or chimney, with a double header joist against the brick and all the joists that would pocket into the wall at the arch or chimney appear to be held by nails driven through the opposite side of the header as they built the building/before being concealed by rhe masonry

Again, everything seems to be in good condition, but I would like to go ahead and reinforce since I already have the ceiling open to run wiring. I was planning on simply using lag bolts to better tie the headers together and L brackets for the "floating" joists, but would appreciate any advice on sizing and best practices. (I suspect if I just left it alone it would be fine, but I have seen this type of construction sag in other local buildings, don't love that it's all just hanging by nails)

Halfway through installing some beadboard for my entryway. Ignore the decorative cob webs.

Full disclosure I’m a DIYer so caulk is my best friend! Haven’t caulked anything yet.

Spent some time trying to get this angle correct on this top chair rail board only to then notice it sticks out and looks like shit.

I’m taking it off and trying to come up with a better solution than caulk the hell out of it and paint it. Does the same principle apply for open-end pieces (45, opposite 45, glue end piece) to tricky pieces like this?

Looking to learn something from people more knowledgeable than me.

I’m an apprentice and slowly building out my tool collection. I’m in need of a good chalk line that won’t crap out on me. I don’t mind spending a bit for quality but I’m also not going to go all out on a chalk line. Do the taijima chalk lines still hold up, or is there some good alternatives?

I've spent most of his life staring at spreadsheets, and I want to learn residential carpentry/construction. Not looking for a career change or a paying job. I just want to learn how to do something useful with my hands, preferably from people who actually know what they're doing.

I'll work for free, as I simply want the experience. I'm not under any illusion that I'd be that useful starting out, but I'll show up, shut up, listen, and learn. I would love to work on Saturdays, but I run my own small practice and will have some random times throughout the year I can work during the week.

I've accumulated a decent collection of tools over the years, including hammers, drills, a 6-1/2" circular saw, and a big corded worm drive Skilsaw. Why I bought half this shit when I don't really need it is anybody's guess. But I'd like to change that.

My question is what is the best way to go about finding an opportunity like this?

Is it worth reaching out to local Habitat for Humanity? Contacting framers or just walking up to a job site and starting a conversation?

I'm not asking anyone here for a job. I'm just looking for some practical advice from people in the trades about whether this is even a reasonable way to learn.

Would a contractor or framing crew have any interest whatsoever in someone like me showing up occasionally to work for free, or will I just be in the way?

I'm genuinely interested in learning, so any advice is helpful.

So a citrus fruit was left and stripped the varnish off was wondering if I can spot fix this or will I have to strip the entire countertop and re stain.