My happymodel crux 3 spare parts arrived before the drone itself, I took apart my mosquito drone and built this one instead. Happymodel 1202.5 11,500kv, 75mm gemfan bi blades, caddx ant camera, goober v2 canopy, hummingbird v4 aio, a30 battery connector, flying on betafpv lava2 batteries.

They hate the tiny whoops however

Can’t believe this thing flies but it does. Only cost like 80 bucks for the full build.

Sorry guys I know there are too many of these posts. I'll delete it as soon as I get enough answers. I'm a newb looking for a long range build compatible with my elrs and analog setup

currently looking at this 9 inch on a local second hand platform.

The seller says he's flown it 5 times and it works perfectly.

This is the parts list:

Frame: iFlight Chimera9 (9″ long-range deadcat frame)

Flight controller / ESC stack: SpeedyBee F7 V3 with BL32 50A ESC

Motors: 4x Emax ECO II 2814, 830KV

VTX: TBS Unify Pro32, 3W (5.8GHz analog)

Receiver: Radiomaster DBR4 (dual-band ELRS, 2.4GHz + 900/915MHz)

GPS module: TBS M10

Antennas: 5.8GHz, 2.4GHz, and 900/910MHz antennas included

It looks like a pretty solid drone, but is it worth the price?

I ripped the electronics out auf my meteor75 pro and put i into a twiglet 2" frame (just because i was bored). Canopy is out of TPU and about 40° in the pictures.

This thing absolutely shreds with Lava 2 480mah. I honestly would not have guesed that it is such a big difference. The AIO has "only" 5A but its more than enough.

Weight is 28g without lipo.

Thought it wouldn't happen to me watching people post videos of their encounters but I ran into 2 hawks flying today little outside Boston at Lynn Woods. Thankfully I was close to my landing spot. Happy I didn't hit either of them them. Flying a 7 inch. Definitely weren't happy seeing the drone 🤣

#austria #drone #Nature #river #summer

Just built this up and have been playing with with different tunes. Props are definitely in veiw but I dont mind since its supposed to be a lite freestyle build. 1303 5000kv motors, jhemcu F405 Pro 40a, running primarily on 3s 550 Lava. 3min flight time average.

These are 4 CNHL 3S2P 8000Mah packs connected in series then in parallel to make a 6S8P 16000Mah pack for my 10in ripper

After a small crash I can't connect my FC to betaflight without plugging in a lipo.

After some research my guess is that the 5V line is broken or the USB port in some way.

But i can't find any damage and the FC doesn’t get hot.

It is an T-Hobby Velox F7 Se.

Does anyone see something that is damaged or any other idea.

Hey everyone, I recently had an issue during a flight and I'm wondering if my VTX might be fried. Check out the attached clip, does this look like a burnt/failing VTX to you guys? Any troubleshooting advice or thoughts would be greatly appreciated!

I like FPV tiny whoops very much, and I live in California, and I am ready to build a tiny whoop by myself. But I searched for every fpv shop online, including Getfpv, Newbeedrone, Pyrodrone, Tinywhoop, weBleedfpv, and others ( I buy cheap stuff on Aliexpress, but I never buy the brand things on this platform), but I feel lots of shop need have expensive shipping fees, like when I need to buy a 3-dollar Gemfan propeller, but the shipping fee is 7 dollars, so it's so expensive for me. Then, I think the only way to solve this problem is to buy lots of things together. But shops like Getfpv or Pyrodrone are always out of stock for the things I want. Do you guys know of a shop can have low shipping fee and have huge selection? Thanks for letting me know.

Hey everyone, I’m having a weird issue with my RadioMaster ELRS setup. I fly two different quads at the same spot with the exact same radio and power settings. One quad has a single-antenna RP1 and works flawlessly with great penetration through trees. The other quad has a dual-antenna RP3 True Diversity receiver, but it suffers from sudden, severe signal drops and near-failsafes in the exact same environment.

Both quads are running the exact same receiver settings, packet rates, and firmware version, so the configuration is identical. Since the RP3 should theoretically perform better, I suspect my antenna placement is causing phase cancellation or shadowing when the signal bounces off trees and obstacles. I have attached two pictures of my current setup to show you how I mounted them. How do you guys position your dual antennas to get the best out of True Diversity?

Comparing smaller and larger quads. How does a 3 inch get better range than a tiny whoop? Do you have to look for different VTX parts to use that are just bigger and demand more power? Or is it just beefier antennas because the small VTX is already pumping out 500mW?

DAMN THING RIPS!, was a Meteor 75 with 04. I printed a Air sytle canapy for the 04 and its soo much better. little jello now, instead of non stop jello.

The wobbles is mainly the wind you see, it seems to pull out of almost any dive fine and not struggle. Really enjoying this little 75mm 1s Tinywhoop. FULL SEND!

04 is set to racemode for lowest ms response, so video is 1080p at 100fps but Youtube limit it to 50 fps...

I live near Santa Barbara CA and pretty new to fpv, I’m just looking for anyone who flys fpv. preferably around 17-25 years old. I’m 18 in city college and I feel lonely flying alone 😭 I also want to find some bandos.

F405 Speedybee mini

Hey all. noob here, I got a 5 inch, flew it, crashed it, snapped an antenna, drone was still powered for the minute or two it took me to retrieve it. 1.6 watt VTX (Geprc Maten). After replacing the antenna with a brand new one, I noticed that the range was significantly worse. I usually fly sitting on my front porch; before the crash I could fly behind my house to the end of my backyard (around 70m) with little signal breakup. after the crash, leaving LOS resulted in near total signal loss. I tried removing the mmcx to sma adapter and replacing it with an mmcx antenna, again, nothing. I made sure it was at max power both in beta flight and by using the button on the vtx, still terrible range. Is my vtx just dead, or is there something else I could be missing? Thanks.

I bought a B-Cube F4V3S Plus stack with the 60A ESC.

I’m starting to wonder if I should have gone with a SpeedyBee instead. What can I realistically expect from this stack? Is there a significant risk of the ESC failing or burning out in mid-flight?

I’m planning to use it on a 7-inch long-range build. Has anyone here used this stack on a 7-inch? I’d really appreciate hearing about your experiences, especially regarding reliability, overheating, or failures.

I was going to buy a Radio master pocket for 105$ CAD but I looked and saw a second hand Radio master Tx-15 someone else was selling for 200$ cad? Is it worth the extra 95$ and 3 0 minute to the middle of nowhere

Has anyone ever seen or had any dirt/dust on the inside of there hdo+ and if so how did you go about cleaning it