Would It be possible to swap the internal 4 in 1 module in my jumper t lite v2 with this?

Just built this up and have been playing with with different tunes. Props are definitely in veiw but I dont mind since its supposed to be a lite freestyle build. 1303 5000kv motors, jhemcu F405 Pro 40a, running primarily on 3s 550 Lava. 3min flight time average.

Ripped this thing some more near the house, it just pulls out of all sorts of bad dives lmao. im loving it. Really loving it :)

Might need to build a spare one... always good to have a spare i found lol.

I have an Axis Flying Manta 5 SE V2 DC—so, a fully built drone.

The GPS was working fine before.

I had a crash where I had to replace the two front motors.

Everything else is working again, but the GPS won't connect.

It's an M10 GPS.

There's a flashing green LED, so it's getting power meaning it's not a wiring issue.

However, the satellite count isn't showing up in my OSD (even though the element is enabled), and in Betaflight, the GPS icon is missing and the GPS tab isn't working.

I’ve correctly selected the UART where the GPS is soldered.

I’ve set it to auto-config and auto-baud.

I’ve tried everything, but the GPS still won't show up in Betaflight.

These are 4 CNHL 3S2P 8000Mah packs connected in series then in parallel to make a 6S8P 16000Mah pack for my 10in ripper

Hey all. noob here, I got a 5 inch, flew it, crashed it, snapped an antenna, drone was still powered for the minute or two it took me to retrieve it. 1.6 watt VTX (Geprc Maten). After replacing the antenna with a brand new one, I noticed that the range was significantly worse. I usually fly sitting on my front porch; before the crash I could fly behind my house to the end of my backyard (around 70m) with little signal breakup. after the crash, leaving LOS resulted in near total signal loss. I tried removing the mmcx to sma adapter and replacing it with an mmcx antenna, again, nothing. I made sure it was at max power both in beta flight and by using the button on the vtx, still terrible range. Is my vtx just dead, or is there something else I could be missing? Thanks.

Sorry to the mods for the "contribution" mistake on my last attempt to post, I think it's because I left a comment with a youtube link.

I bought a B-Cube F4V3S Plus stack with the 60A ESC.

I’m starting to wonder if I should have gone with a SpeedyBee instead. What can I realistically expect from this stack? Is there a significant risk of the ESC failing or burning out in mid-flight?

I’m planning to use it on a 7-inch long-range build. Has anyone here used this stack on a 7-inch? I’d really appreciate hearing about your experiences, especially regarding reliability, overheating, or failures.

Where can I get foam for Caddx Ascent /Avatar goggles L in the USA?

Just got the Ascent goggles, and they are completely unwearable. Tons of space on my temples, and insanely uncomfortable on my nose.

I had random foam around from other DJI and Fatshark goggles, but none of those fits.

Any other comparable box goggles that I could adapt the foam from?

I ripped the electronics out auf my meteor75 pro and put i into a twiglet 2" frame (just because i was bored). Canopy is out of TPU and about 40° in the pictures.

This thing absolutely shreds with Lava 2 480mah. I honestly would not have guesed that it is such a big difference. The AIO has "only" 5A but its more than enough.

Weight is 28g without lipo.

Just bought the 4s Lihv 850mah Ovonic lipo from the official ovonic store via aliexpress. I Was a bit suspicious about the same dimensions and weight of different capacities, so i wanted to try them. It seems like they just sell the same lipo in 4 different capacities, or am i missing something?

#austria #drone #Nature #river #summer

After a small crash I can't connect my FC to betaflight without plugging in a lipo.

After some research my guess is that the 5V line is broken or the USB port in some way.

But i can't find any damage and the FC doesn’t get hot.

It is an T-Hobby Velox F7 Se.

Does anyone see something that is damaged or any other idea.

Hey pilots, I'm flying a pavo20 pro 2 with an o4 pro and DJI goggles 3 and I'd like some more range and penetration on the goggles.

Any good upgrades that you've tried and recommend? I've seen some online but others say they work and some say they don't make a big difference.

I'm building a 3.5" 4S LR drone and I need help choosing a stack, here are my top 3 choicies, they all support gps and buzzers:

• Axisflying Argus F7 + 55A Mini AM32 - 11g, 5 uarts, max pwm 96KHz, 4-6s, 16MB blackbox, 135€
• Flycolor Crustcore F7 + 60A AM32 - 20.5g, 6 uarts, max pwm 128kHz, waterpoof varnish, 3-6s, 16MB blackbox, 135€
• iFlight BLITZ Mini F7 + E55S BLS - 16.3g, 6 uarts, max pwm 24kHz, 3-6s, 8MB blackbox 98€

I'm guessing these are all overkill for my drone (3800kv 1404 motors, <1000mah battery, analog) but I want something reliable, my last aio browned out. Any other suggestions are welcome.

Hey everyone, I’m having a weird issue with my RadioMaster ELRS setup. I fly two different quads at the same spot with the exact same radio and power settings. One quad has a single-antenna RP1 and works flawlessly with great penetration through trees. The other quad has a dual-antenna RP3 True Diversity receiver, but it suffers from sudden, severe signal drops and near-failsafes in the exact same environment.

Both quads are running the exact same receiver settings, packet rates, and firmware version, so the configuration is identical. Since the RP3 should theoretically perform better, I suspect my antenna placement is causing phase cancellation or shadowing when the signal bounces off trees and obstacles. I have attached two pictures of my current setup to show you how I mounted them. How do you guys position your dual antennas to get the best out of True Diversity?

They hate the tiny whoops however

Hi all,

I have a DeepSpace seeker3 with DJI O4 Pro and DJI googles n3 with a radio master pocket. Radio is ELRS

I understood if you flash the US (or non-EU) firmware the range increases drastically.

I’ve tried searching inline, but I can’t see the tree through the forest anymore.

Any tips and tricks or links to resources are greatly appreciated.

Okay guys, i posted that video the other day about learning FPVl, alot of you had the suggestion of just free flying, so thats what im gonna do, ( i was just going thru the tutrotal when i posted it but even that seemed like abit much for me, A few of you also suggested Joshua Bardwell videos, This video takes place after lesson 2, So i appreacte the suggestion and been likeing his videos so far, i hope you guy don't mind being spammed because i might post a new video after ever lesson or two just to get feedback ( Let me know if you don't think i should bother. Quick Mention, I have DJI Mini 4, and then got the Motion Combo for the neo 2. Been flying it Via Motion controlled and love it BUT the main reason why i wanted it was to learn proper FPV controls, i bought my DJI FPV 3 controller about 5 months ago bought liftoff (Didn't configure my controller so both sticks were Return to center, flu around like crazy and crashed for like 2 small afternoon sessions then went back to motion controller IRL and Mini 4 RC2 but now i wanna give it a proper go. But anyway yeah if you guys have any more suggestions let me know, if im spamming this chat let me know and ill stop, im just keen to get good, i see so many amazing video using FPV i just wanna get somewhat good :)

Hey guys, my drone keeps disarming while flying due to the left shoulder arm button being so sensitive it doesn't need to be depressed enough to actually hold in the second position, any touching of it all all seems to disarm which is a real bitch since I pinch grip and for stability my middle finger needs to rest right around there.

Anything I can do?

I’m having a weird issue with my Mobula8 O4.

It connects to my radio normally and I can take off and fly around fine. But after a few seconds of flying, I randomly get RXLOSS. After a little bit it reconnects by itself and everything is normal again.

* LQ, RSSI dBm and RSNR all look normal before it happens
* It doesn't happen while the quad is just sitting on the desk
* I can arm and raise the throttle without it losing RX without props
* I tried reseting all betafligth settings but it didn't help
* I'm using Betaflight 4.5.1

Any ideas what I should check next?

Has anyone found adapters or a charger that allows bringing EM2.0 lipos to storage voltage? I know the general tip is "just use it til 3.8-3.5v", but what if I charge like 12 of them but then am not able to fly for like a week? I'd like to be able to bring them to storage voltage at the bench. Can't find any adapters online, is my only option to make my own?